Right now Im at that 30-60 range but I guess my main issue is that the router and my laptop are seperated by the kitchen
I'll see if I can move some stuff around. If not a booster or antenna may be the option. Thank for the input.
| Avian Gamers Network http://www.avian-gamers.net/forums/ |
|
| WiFi boosting? http://www.avian-gamers.net/forums/viewtopic.php?f=1&t=14831 |
Page 1 of 1 |
| Author: | iJasonT [ Thu Jun 02, 2005 3:57 pm ] |
| Post subject: | WiFi boosting? |
I just moved into a new apartment and my WiFi router is in the middle of the apartment and my room where I keep my laptop is in the rear of the place. My WiFi signal sucks in the back room, is it possible to boost a WiFi signal? |
|
| Author: | Arindel [ Thu Jun 02, 2005 4:15 pm ] |
| Post subject: | |
There is a device called "booster" funny enough that will increase the signal strength to give you a larger radius. also, you could use a device called a repeater, that will intercept the signal and pass it along to your pc and/or router. This might be the best optino for you as you have a direct space that is being affected, but either solution should work. I went with a booster so I could use my laptop in the great outdoors at my house. in an apartment, you may not want to boost your signal as that will push it out to more of your neighbors. |
|
| Author: | X2-PB [ Thu Jun 02, 2005 4:21 pm ] |
| Post subject: | |
I've noticed that the signals don't like RSJs (Reenforced Steel Joists) so make sure there are none between the router and the laptop. |
|
| Author: | Master Gui-Jan [ Thu Jun 02, 2005 5:49 pm ] |
| Post subject: | |
A few other options, Make sure your Router is high, around eye level. That requires the signal to go through less solid matter, which tends to interfere with signal strength. Make sure that there are no major appliances or electronics between the router and the laptop. A refridgerator or microwave will destroy a wireless signal. Also, many routers have booster antenna's you can get to replace your current one(s). These tend to work if you are only getting between 30% and 60% reception, like 2 or 3 bars on a 5 bar scale, but won't help you if you are getting less than 30%, 1 bar. |
|
| Author: | iJasonT [ Thu Jun 02, 2005 5:59 pm ] |
| Post subject: | |
Right now Im at that 30-60 range but I guess my main issue is that the router and my laptop are seperated by the kitchen
I'll see if I can move some stuff around. If not a booster or antenna may be the option. Thank for the input. |
|
| Author: | bigyak [ Thu Jun 02, 2005 6:43 pm ] |
| Post subject: | |
From a paper I wrote, might be of use (let me know if you want sections I,II and IV on how to hack into WLANs.  ):
III. PHYSICAL WIRELESS CONFIGURATION Requirements for wireless systems vary based on organizational size, geographical spread, security requirements and many other factors. The first step to implementing a wireless system is to gain a keen understanding of radio wave behavior, and to know the different ways that waves propagate. Omni-directional antennas have a 360-degree cover pattern. The waves that they emit radiate outwards in a doughnut-shaped pattern with the antenna at the center of the doughnut hole. Waves are transmitted uniformly in every direction, though wind up being reflected from ceilings and floors, resulting in a squished-doughnut propagation pattern. <<Fig. 1>>. Omni-directional and directional antenna radiation patterns. Directional antennas transmit data in one direction, almost like the beam of a headlight. Beams can be focused to provide longer, more directional coverage. As with omni-directional antennas, 802.11 signals can penetrate through brick and concrete. Windows and doors allow much more signal leakage. Most access points use omni-directional antennas, though some allow replacement antennas to be swapped in. Most stations do not allow replacement antennas, though are easily modifiable with a screw-driver and a soldering iron. It is important to note that radio equipment from vendors may not be modified due to FCC regulations. Within the US, Equivalently Isotropically Radiated Power is restricted by the FCC to four watts maximum, with additional restrictions depending on the type of antenna. After considering different antennas and frequencies, it is a good idea to construct a map of the current network infrastructure and list the requirements that the wireless system will address. Carefully consider the following questions: • Who needs wireless access? All employees? Inventory clerks? Business executives? • What existing resources should each group be allowed to access? • How many members need this access? What bandwidth will they require? • Are there main gathering points that will need to support a larger load? Will users be mobile, such as in a warehouse or emergency response zones? • What classification of materials is needed for each zone? • Do any zones need access to the Internet? Most large-scale business networks using 802.11b rely on non overlapping channels. The 802.11b standard is broken up into 11 separate sub-channels. Each of these channels slightly overlap each other to allow users to load-balance across multiple channels, and achieve 11Mbps throughput on each channel. Channels 1, 6 and 11 allow the greatest range of non-overlapping frequency, and provide users with the greatest range of useful signal space. Because of this, many companies with 100s of users in a close area tune their access points to use these three sub channels, and space them in a hexagonal pattern over their target area. It is important to note that many experienced wireless intruders hoping to access business networks often attempt to gain access to WLANs on these frequencies first. It is important to note that different countries have different allowances for channel and frequency use. Some other general radio frequency issues: • Radio data rates decrease with range • Range usually increases proportional to antenna height • Open areas provide better radio range • Steel pillars, concrete, microwave ovens and water are barriers to radio waves • In sitting areas, try to point client antennas at the access point • Conduct surveys during normal business hours • Implement wireless security procedures on access points |
|
| Author: | iJasonT [ Thu Jun 02, 2005 7:16 pm ] |
| Post subject: | |
just goes to show why Yak is my own private jesus. |
|
| Author: | bigyak [ Thu Jun 02, 2005 7:37 pm ] |
| Post subject: | |
Hey now, I wouldn't go that far. That dude had some major coolness. I'm just good with the Google. And I'd think that, after working with Oprah, you wouldn't be so easilly impressed. |
|
| Author: | iJasonT [ Thu Jun 02, 2005 8:33 pm ] |
| Post subject: | |
reminds Yak that I am a peon there and that yes, I am easily impressed. Want proof? I still play SWG! |
|
| Author: | dbakke [ Thu Jun 02, 2005 9:09 pm ] |
| Post subject: | |
LOL@Moge |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|